KODE ERROR AC TCL

"CV.citra teknik"

jln Wadas IV no.2 Jati  Cempaka pondok Gede

021 8499 8580 -- 021 8499 7906      Hp =  0813 1040 1011

Email ; citra_teknik29@yahoo.co.id

TCL Error Code Failure type = In and out communication failure LED CODE = RUN,TIMER -both winking DIGITAL LED CODE = E0  Failure type = Outdoor communication failure LED CODE = RUN,TIMER -both winking DIGITAL LED CODE = EC  Failure type = Outdoor sensor LED CODE = RUN-1 time/8s DIGITAL LED CODE = E1  Failure type = Indoor coil temperature sensor LED CODE = RUN-2 times/8s DIGITAL LED CODE = E2  Failure type = Outdoor coil temperature sensor LED CODE = RUN-3 times/8s DIGITAL LED CODE = E3 Failure type = System abnormity LED CODE = RUN-4 times /8s DIGITAL LED CODE = E4  Failure type = Type mismatch LED CODE = RUN-5 times /8s DIGITAL LED CODE = E5  Failure type = Indoor fan motor LED CODE = RUN-6 times /8s DIGITAL LED CODE = E6  Failure type = Outdoor temperature sensor LED CODE = RUN-7 times /8s DIGITAL LED CODE = E7  Failure type = Discharge temperature sensor LED CODE = RUN-8 times /8s DIGITAL LED CODE = E8  Failure type = Invert module abnormity LED CODE = RUN-9 times /8s DIGITAL LED CODE = E9  Failure type = Outdoor fan motor (DC)  LED CODE = RUN-10 times /8s DIGITAL LED CODE = EF  Failure type = Current sensor LED CODE = RUN--11 times /8s DIGITAL LED CODE = EA  Failure type = EEPROM failure LED CODE = RUN-12 times /8s DIGITAL LED CODE = EE  Failure type = Top of compressor temperature switch LED CODE = RUN-13 times /8s DIGITAL LED CODE = EP  Failure type = Voltage sensor LED CODE = RUN-14 times /8s DIGITAL LED CODE = EU  Protection display code list: Protection type = higher or lower voltage LED CODE = RUN-winking,TIMER-1 time/8s  DIGITAL LED CODE = P1  Protection type = Over current LED CODE = RUN- winking,TIMER-2 times /8s DIGITAL LED CODE = P2  Protection type = Discharge temperature LED CODE = RUN- winking,TIMER-4 times /8s DIGITAL LED CODE = P4  Protection type = Over cooling in cooling mode LED CODE = RUN-light,TIMER-5 times /8s DIGITAL LED CODE = P5  Protection type = Over heating in cooling mode LED CODE = RUN- light,TIMER-6 times /8s DIGITAL LED CODE = P6  Protection type = Over heating in heating mode LED CODE = RUN- light,TIMER-7 times /8s DIGITAL LED CODE = P7  Protection type = Outdoor temperature too high or low  LED CODE = RUN- light,TIMER-8 times /8s DIGITAL LED CODE = P8   Protection type = Drive protection(Overload) LED CODE = RUN- winking,TIMER-9 times/8s DIGITAL LED CODE = P9  Protection type = Module self protection LED CODE = RUN- winking,TIMER-10 times/8s DIGITAL LED CODE = P0  Outdoor failure display There is a LED on outdoor power board, when compressor is running; it is normally light; when no feedback of signal to power board from compressor, it will wink by lighting 1s and going out 1s. If failures happened, it will light 0.5s, go out 0.5s, winking several times and go out 3s for a cycle to indicate failures. The failure list is the follow:  Wink time = 1 Failure = IPM protection  Wink time = 2 Failure = higher or lower voltage Wink time = 3 Failure = Over current  Wink time = 4 Failure = Discharge temperature too high  Wink time = 5 Failure = Outdoor coil temperature too high  Wink time = 6 Failure = Drive abnormity  Wink time = 7 Failure = Communication abnormity with indoor unit  Wink time = 8 Failure = Compressor over heat (switch on top of compressor)  Wink time = 9 Failure = Outdoor air temperature sensor failure   Wink time = 10 Failure = Outdoor coil temperature sensor failure  Wink time = 11 Failure = Outdoor discharge pipe temperature sensor failure